东莞市宝韵自动化设备有限公司

DONGGUAN BAOYUN AUTOMATION EQUIPMENT CO., LTD

BOS-6F-600自动调带分离式粘合机
分享到:

BOS-6F-600自动调带分离式粘合机

产品详情

1.本机优化设计的气压调偏正系统,以及无需延时关机,解决待机,和下班提前关机的问题。同时延长输送带的寿命,降低了能效,更人性实用。

2.采用独立两段粗辊加压系统,第一段压力将衬布上的胶粒均匀分布,第二段压力系统将溶解的胶粒和面料到更理想的粘合效果。两段加压系统分别独立控从而实现不同的压力组合,使布料和衬布达到完美的融合。

3.采用弯弧形上下两段加热区,使输送带更好的贴合布料加热器以达到最佳的热传递,提高热效率,可适应各种难粘合的面(如免烫面料和麻料)加热区的温度可以单独控制,以满足更高的要求。

4.采用内涨紧走带方式,使滚轴不易粘上灰尘污溃,达到不会再污染面料,及造成皮带的损坏。皮带采用里外双重清洁装置可对皮带的里外两面进行自动清洁,从而使皮带的使用寿命得到提升。

5.采用强制水冷却装置,对粘合的裁片,进行快速冷却处理,达到降温和稳定了粘合的效果。

6.可视化加热系统,压力系统,皮带修正系统,使机器维修保养更简便。

7.尺寸(450mm- 1200mm),特殊功能(风冷,水冷,回转剥离装置,等)可针对工厂需要进行定制

8.采用高温户外烤漆,牢固耐磨,保持10年以上不退色。


1. The optimized design of the air pressurecorrection system, and no need to delay shutdown,to solve the problemof standby and early shutdown after get off work. At the same. time,the life ofthe conveyor belt is extended,energy efficiency is reduced, and it is morehuman and practical.

2. Adopt independent two-stage thick rollerpressure system, the first stage pressure will evenly distribute the rubberparticles on the 1 ining, the second stage pressure system will dissolve the rubber particlesand the fabric to a more ideal bonding effect. The two-stage pressure system isindependently controlled to achieve different pressure combinations,so that thefabric and interl ining achieve a perfect fusion.

3. The curved upper and lower heating zonesare adopted to make the conveyor belt better fit the fabric heater to achievethe best heat transfer, improve thermal eff iciency, and adapt tovarious difficult-to-bond surfaces (such as non-iron fabrics and Hemp material)The temperature of the heating zone can be individually controlled to meethigher requirements.

4. Adopting the internal tensioning belt travelmethod, so that the roller is not easy to stick to dust and stains,so that itwill no longer pol lute the fabric and cause damage to the belt. The beltadopts a double cleaning device .inside and outside,which canautomatically clean the inside and outside of the belt,so that theservice life of the belt is improved.

5. Using a forced water cooling device toquickly cool the bonded pieces to cool down and stabilize the bonding effect.

6. Visual ized heating system,pressuresystem,belt correction system,making machine maintenance easier.

7. Size (450mm- 1200mm), specialfunctions (air cooling, water cool ing,rotary peeling device,etc. ) can be customized according to the needs of the factory.

8. The use of high-temperature outdoorbaking varnish is firm and wear-resistant,and will not fadefor more than 10 years.


源自 BOSTSEW   从定义缝纫机